TEL TAC II error code?

welder · 5/18/08, 8:05 PM

does anyone know what E1 then 08 flashed on tac means?
engine would not run down the straightaway, pulled ok off the corner then went flat and lost power down the straight.
Danny Williams Jr.

welder · 5/18/08, 8:21 PM

Does anyone know what E1 then 08 flashed on tac means? Engine pulled well off the corner then went flat and lost power down straight.

Danny Williams Jr.

posted in tech as well

Rex W. · 5/18/08, 8:37 PM

Jr. I'll look at some info i got at work & let ya know in the morn.

Eric C · 5/18/08, 8:50 PM

Error Codes: E1: This indicates the unit did not follow its normal sequence and had to restart itself.
This code may rarely appear if motor is started at the exact instant the tach was shuttung off--- Reading would still be OK.

This is what the Tel Tac manual says.

Eric C

welder · 5/18/08, 8:56 PM

Rex, check pm

Thanks Eric C

wobbler · 5/18/08, 11:52 PM

Danny according to the Tel Tac instruction sheet code 'E1' reads as follows:

Error Codes. Unit may flash an error code after the engine is stopped along with the RPM reading (reading may not be correct)
E 1 This indicates the unit did not follow its normal sequence and had to restart itself. This code may rarely appear if motor was started at the exact instant the tach was shutting off- reading would still be OK.

mrmoose · 5/19/08, 3:01 PM

danny call this guy and he will get ya set straight.
TelTac

% James Haussler

2183 White Lane

Stockton, CA 95215

209-931-6854

5/18/08, 8:05 PM	#1 TEL TAC II error code?
welder Member Join Date: Jul 2007 Posts: 197	does anyone know what E1 then 08 flashed on tac means? engine would not run down the straightaway, pulled ok off the corner then went flat and lost power down the straight. Danny Williams Jr.

5/18/08, 8:21 PM	#2 TEL TAC II error code?
welder Member Join Date: Jul 2007 Posts: 197	Does anyone know what E1 then 08 flashed on tac means? Engine pulled well off the corner then went flat and lost power down straight. Danny Williams Jr. posted in tech as well

5/18/08, 8:37 PM	#3 Re: TEL TAC II error code?
Rex W. Senior Member Join Date: Jul 2007 Posts: 295	Jr. I'll look at some info i got at work & let ya know in the morn.

5/18/08, 8:50 PM	#4 Re: TEL TAC II error code?
Eric C Member Join Date: Aug 2007 Posts: 156	Error Codes: E1: This indicates the unit did not follow its normal sequence and had to restart itself. This code may rarely appear if motor is started at the exact instant the tach was shuttung off--- Reading would still be OK. This is what the Tel Tac manual says. Eric C

5/18/08, 8:56 PM	#5 Re: TEL TAC II error code?
welder Member Join Date: Jul 2007 Posts: 197	Rex, check pm Thanks Eric C

5/18/08, 11:52 PM	#6 Re: TEL TAC II error code?
wobbler Member Join Date: Jul 2007 Posts: 191	Danny according to the Tel Tac instruction sheet code 'E1' reads as follows: Error Codes. Unit may flash an error code after the engine is stopped along with the RPM reading (reading may not be correct) E 1 This indicates the unit did not follow its normal sequence and had to restart itself. This code may rarely appear if motor was started at the exact instant the tach was shutting off- reading would still be OK.

5/19/08, 3:01 PM	#7 Re: TEL TAC II error code?
mrmoose Member Join Date: Feb 2008 Posts: 68	danny call this guy and he will get ya set straight. TelTac % James Haussler 2183 White Lane Stockton, CA 95215 209-931-6854