12 tooth engine gear?

DAVE BOOS · 3/26/16, 5:51 PM

Anybody know where you can get a 12 tooth engine gear for an 07-08 R1? See a lot of 13's available but can't find a 12 thanks!

dirtrack · 3/26/16, 8:21 PM

It is the same spline as a 04 and up Honda 600RR. South West Speed (AKA Kratter) sells them on EBay for 29.99 It will be a narrow 520 sprocket, but works fine.

Bill84 · 3/26/16, 9:12 PM

Speed Partz

http://www.speedpartz.com/frontsprockets.htm

Bill

DAD · 3/27/16, 9:31 AM

Dave

Those 12 tooth sprockets are really hard on chains, I would look for a rear sprocket with a few more teeth on it. We started using really big rear sprockets (54-61 teeth) a long time ago. They allow us to use more (higher) gears in the transmission and also allow us to have much smaller gear ratio splits than them little 42-50 tooth sprockets. You will have to fabricate larger pizza pans

.

Honest Dad himself

jdull99 · 3/28/16, 12:10 AM

Will one that works on an R6 work?

DAVE BOOS · 3/28/16, 1:15 AM

Thanks guys for info! Just trying to figure out a gear set for a 1/6th mile track, we normally run 1/4-3/8 mile tracks.

Jim Gardner · 3/28/16, 7:41 AM

Go to hyper's site and look at the ratios to run in first gear. That's a much better option than to change the mechanical gearing, where you'll have to worry about adjusting chain length, wheelbase, etc.

dirtrack · 3/28/16, 4:50 PM

R6 sprockets are smaller spline and will not work.

DAD · 3/28/16, 5:29 PM

Dirt

Aren't the splines the same? They newer r6 might use a 520 chain as opposed to 530 used on the early R6 The 520 is just a little bit thinner but I think we have interchanged them in the past with our zx10R motor with little damage to chain. Thought Honda had the only different spline courser?

Honest Dad himself

DAVE BOOS · 3/28/16, 5:57 PM

That's a good idea Jim I'll do that! I don't want to have to change chain length and all that mess.

3/28/16, 12:10 AM	#5 Re: 12 tooth engine gear?
jdull99 Senior Member Join Date: Nov 2008 Posts: 6,406	Will one that works on an R6 work? __________________ Jason Dull 815 494 6002 jdull99@hotmail.com

3/28/16, 5:29 PM	#9 Re: 12 tooth engine gear?
DAD Senior Member Join Date: Aug 2009 Posts: 5,957	Dirt Aren't the splines the same? They newer r6 might use a 520 chain as opposed to 530 used on the early R6 The 520 is just a little bit thinner but I think we have interchanged them in the past with our zx10R motor with little damage to chain. Thought Honda had the only different spline courser? Honest Dad himself _________________________________________________ Last edited by DAD; 3/28/16 at 5:31 PM.

3/26/16, 5:51 PM	#1 12 tooth engine gear?
DAVE BOOS Member Join Date: Mar 2014 Posts: 53	Anybody know where you can get a 12 tooth engine gear for an 07-08 R1? See a lot of 13's available but can't find a 12 thanks!

3/26/16, 9:12 PM	#3 Re: 12 tooth engine gear?
Bill84 Member Race Count This Year: 17 Race Count Last Year: 13 Join Date: Nov 2008 Posts: 172	Speed Partz http://www.speedpartz.com/frontsprockets.htm Bill

3/28/16, 1:15 AM	#6
DAVE BOOS Member Join Date: Mar 2014 Posts: 53	Thanks guys for info! Just trying to figure out a gear set for a 1/6th mile track, we normally run 1/4-3/8 mile tracks.

3/28/16, 5:57 PM	#10
DAVE BOOS Member Join Date: Mar 2014 Posts: 53	That's a good idea Jim I'll do that! I don't want to have to change chain length and all that mess.