[vyper]

I will sell roller only or engine only or complete!!! PRICE DROPPED TO $25,000.00 cash

2013 Maxim 87/40 RR with Mopar originally a Stanton built engine,Engler injection,Engine fired never been on the track! New everything but cam lifters , rockers and push rods, sleeved back to std, has JE pistons, total seal rings,Del West ti valves and retainers,Isky tool room springs, Clevite coated bearings, oliver rods, REM finished Bryant crank Rev Chipped at 8k, Winters rear, King torque tube, Waterman, Kinsler components,! Msd, Pro tach, New KSE 1/2 box, big master cyl w/ three brake set up. chassis has Smith bar option, right side bar option, Swidell seat system, Hooker belts with ratchet, Ultrasheild seat. Full body work. This car is top shelf there is nothing it needs, clean not battle scarred!!!

$25,000.00 cash price dropped 12/04/16

Will entertain any reasonable offer, . Complete buy out is possible for the right money!

call or text to 217-251-4400 or PM me here for reply

[vyper]

I'm sending this back up the line rather than redoing the whole ad along with my other car. We will sell one definatley do not need both of them would like to do a trade for a Top quality Midget, I have nice stuff and will only trade for nice stuff. Our business and life in general keeps us from racing as much as we would like so we are just slowing down a bit and need to down size our inventory!

[vyper]

I also have lots of brand new parts to sell along with one or the other of the cars. Nerfs, front bumpers, rear bumpers, front axles, radius rods, heims, Pro Shocks, Winters rear ends, nose wings, wing trees, wing struts front and rear, brake pads, plugs, cases upon cases of Kedal racing oil, push lok and nylon braided hose, hose fittings, Keizer Wheels, Sanders Wheels, Weld Wheels, drive shafts, torque tubes, new headers. PARTS WILL NOT SELL UNLESS A CAR IS SOLD someone wants a complete buy of two top quality cars and all spares I'll give you a price!! It's top shelf do not expect fire sale price, I'll be fair but I wont give it away!

[leinacres@gmail.com]

Is the motor raised port w-9, standard w-9.

[vyper]

Not RPW-9 heads they ar the standard port heads, of course its a Chapman CNC port job

[vyper]

$125,000 both cars, plus 32ft 2013 Stacker with lift, new 14ply tires with 100 miles on them ($1,800.00), top observation deck with collapsing railing, Black aluminum cabinets, ball bearing drawers tool cabinet built in 60", rubber coin floor, screw less inside and out, .050 exterior, .04 interior over wood, has all the hangers and such for wings, axles, rear ends, torsion bars,oil and sprays, two hand towel box holder, loft in upper front, alum tire racks. all spare parts 1 new winters rear end, 1 light edm cut gears Ti winters rear used, complete front axles, new nose wings, top wings,multiple complete sets of radius rods, tie rods, ladders, torsion arms, stops, drive shafts, torque tubes, gear sets, torsion bars, shocks (Pro and CSI) 10 fuel bottles, nitrogen bottle and reg, shock filler, axle tool for valve adjusting, new brake pads, brake parts, master cylinders, two bare tail tanks used, spare injection, spare MSD box, torsion rack straightening press, rear rims all bead lock Sanders and Kizer, front wheels, competition water heater, Conroy bleeders, bleeder tank, Van Alstein groover, Wheel wrench, radius rod setter, there's more stuff but these are just the high lights! If anyone wants to get into Sprintcars this is a ton of ultra nice stuff, mostly new very little used equipment.

[vyper]

I have reduced the price on this one also, $31,000.00 complete car, split it $19k for engine, $12k roller.

[vyper]

little rise to the top for another round

[vyper]

to the top again

[vyper]

$28,000 complete car, $11,000 roller, $17,00 engine